Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5758 visitantes online.
Productos
Información
Destacado
Inicio >> SONY >> MDRRF830 Manual de Servicio
 
 0 artículo(s) en Su carrito 

SONY MDRRF830
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SONY MDRRF830 Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
SECTION 2 ELECTRICAL ADJUSTMENTS
Notes: 1. Use transmitter with check and adjustment alreadycompleted. 2. The transmitter section adjustments should be completed before performing the headphones section adjustment. 3. On adjusting the headphones section, use the transmitter as a jig. Headphones MDR-RF830 Transmitter TMR-RF830R

Separation check and adjustment
1. Set the transmitter channel to CH2. 2. Set the transmitter noise filter SW to OFF . 3. Input a signal of 1kHz 316mVrms to onl y the transmitter L4. 5. 6. CH (J403). Connect an digital voltmeter (AC range) and oscilloscope to the L-CH speaker outputs (both sides of MDD01). Receive signals by turning the TUNING VOL (RV302). Adjust the VOL (RV301) so that the RX board L-CH speaker outputs (both sides of MDD01) are 155mVrms. Connect an digital voltmeter (AC range) and oscilloscope to the R-CH speaker outputs (both sides of MDD02) and measure the voltages. At this time, check to make sure the level separation of L-CH and R-CH speaker outputs is more than 20dB. If the separation

Procedure:
AF OSC L-CH (J403) 1kHz 316mVrms (�7.8dB) Jig

7.

ATT

8.
Transmitter 600 � J404 power supply (DC 9V)

1. Feed a signal to jig (transmitter) and connect a power supply to DC IN 9V jack (J404).

Receive frequency check and adjustment
1. Set the transmitter channel to CH2. 2. Set the transmitter noise filter SW to OFF . 3. Input a signal of 1kHz 316mVrms to onl y the transmitter LCH (J403). 4. Place transmitter and headphones at a distance of more than 5m apart. 5. Set the VOL (RV301) to MIN. 6. Position RX board TUNING VOL (RV302) to the center . 7. Connect a digital voltmeter (DC range) and an oscilloscope between IC301 pin @¡ and GND. 8. First check to make sure that a demodulated waveform of 1kHz (appr oximately 13mVrms) is outputted to the oscilloscope , then check to make sure the DC voltmeter reading is DC 1 to 1.2V . 9. If a demodulated waveform of 1kHz is not outputted to the oscilloscope or if the DC level is not within the range specified above, adjust the RX board L301 so that a demodulated waveform of 1kHz is outputted to the oscilloscope and while the wave-form is outputted, further fine adjust the L301 so that the DC voltmeter reading is DC1.1V. 10. When completed, make sure signals can be received when switching the transmitter channel to CH1 or CH3 by turning RX board TUNING VOL (RV302).

is less than 20dB, turn R V303 on the RX boar d so that the RCH output is minimal, then check to see if the level separation of L-CH and R-CH speaker outputs is more than 20dB. 9. Input a signal of 1kHz 316mVrms to only the transmitter R-CH (J402). 10. Adjust the VOL (RV301) so that the RX boar d R-CH speaker outputs (both sides of MDD02) are 155mVrms. 11. Connect an digital voltmeter (AC range) and oscilloscope to the L-CH speaker outputs (both sides of MDD01) and measure the voltages. 12. At this time, check to make sure the level separation of L-CH and R-CH speaker outputs is more than 20dB.

Connection points and Adjustment Location: RX BOARD (See page 5)

Connection points and Adjustment Location: RX BOARD (See page 5)

�4�

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EVO-9850 VOLUME 1 SONY
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.223 - Number of Queries: 127 - Query Time: 0.047